A chair rail is basically a piece of molding that runs along the middle of your room's perimeter. You may want to consider painting the ceiling the same color as your walls, which will help tie the room together and not be such a strong contrast.
Check that the pieces fit properly;
Installing chair rail on uneven walls. I'm not sure if this question really goes here, but it's about assembling my pole room so maybe some of you ladies that are more handy than i am can give me some suggestions. There is a ridge sticking out of the middle of it about 1 inch thick and. Or at some points i have an inch between frame and ceiling, where at other points frame needs to be shaved down.
Apply a generous bead of construction adhesive on the reverse side of the chair rail molding along its length. Take the chair rail down at the concaved area, take a reciprocating saw or circular saw and cut the studs about an 1 1/2 inches in where the chair will cover the cut. So we’ve got a dip in the wall at a chair rail, and after this is painted it would be very obvious and very unsightly.
Have someone go on the others side of the wall and push the studs one at a time toward the curve in the wall. Install short chair rail on return wall. The problem is that the wall is not flat.
Measure each space on the wall where the chair rail will be installed. Uneven ceiling, therefore different height in walls at frames. Bend the rail a bit and caulk it a bit.
In your dining room, consider which walls get the most attention and cope the pieces adjacent to those walls. The general rule is that the chair rail should be about 1/3 of the way up from the floor (between 32 and 36 for an 8’ ceiling). Apply wallpaper or paint high enough (or low enough) for the chair rail to cover the edge.
Around the perimeter of the room. The height at door frames can be flush with ceiling, (80, this is a basement). If you have such a corner, look for an angle measuring device at your hardware store.
Mark the desired distance from the floor to the top of the chair rail (usually 36” to 38”). It’s not terribly noticeable when the walls and trim are in white primer, but it will be once the wall is a different color than the trim. If you're not painting the wall, you just have to split the difference.
Build out the bottom half (wainscoting)to level and parallel using shims, blocking, whatever you need to create a solid backing to nail to. Allow that bottom wall to stand proud of. If your wainscot installation includes inside corners, you’ll have a choice about.
In less than 4 feet. You're right about the chair rail. My ceilings are uneven, it is visible at door frames only.
Cut the chair rail to length. Secure it to the wall with small nails. Measure the wall according to the length to determine how many lengths of chair rail molding will be needed.
To 42 in., with wallpaper either above or below. Install short length of chair rail on long wall. If the top portion is ok with drywall then leave it alone.
Above the floor but can be installed anywhere from 30 in. Installing a chair rail will create a dramatic addition to any room. To determine the height of the chair rail, measure the height of the ceiling and divide it by three.
When terminating the chair rail at the room entrance, you can also cope the ends. Chair rail height is usually 36 in. Sand end of chair rail to remove rough edges.
It doesn't make sense in a room with no chairs near the wall. Depending on your chair rail design, if you split the moulding up into a couple of. Measure and cut any miters for the chair rail, especially if you are turning any corners that are not 90º.
Shim trim and fix uneven walls. If you're painting the wall, use drywall topping to fair out the wall. Lightly mark the bottom of the chair rail every 3 ft.
If you are going to do anything to the walls, i would consider a faux board and batten look. A wall with a window might receive more attention than a blank wall, so butt the coped pieces into a full piece along the window wall. Begin by installing the chair rail molding.
Steps to installing chair rail: Make the chair rail taller in rooms with higher ceilings. Cut the shorter piece of chair rail on the long wall with a mitre box.
Not only does a chair rail protect your walls from furniture, but it can be a creative addition to your interior design, as well. It's the perfect way to makeover a. Mark short chair rail length on return wall.